Weaverine Working Spec Draft
This is a working draft for alignment. Lab reports and GRS or OEKO-TEX documents are confirmed on the order. The PDF uses English export wording.
The 8 mandatory fields on a mill-ready fabric specification sheet
A textile technical data sheet (TDS) or mill RFQ spec sheet aligns buyer and factory on measurable construction targets before lab dips or strike-offs begin. Omitting stage (greige vs finished), width basis (total vs cuttable), or GSM tolerance (±5%) is the single most common cause of bulk sampling delays.
8 PO Fields: Yarn Denier (Warp × Weft) · Sett (EPI × PPI) · Weave · Stage (Greige/PFD/Dyed) · Cuttable Width · GSM (±5%) · Shade (TCX / ΔE ≤ 1.0) · Cert Scope (GRS TC / OEKO-TEX)
Standard Mill Tolerances: GSM ±5% (ISO 3801) · Cuttable Width −0/+2 cm (ISO 22198) · Shade CMC(2:1) ΔE ≤ 1.0 under D65
Usual 30–400. Limit 1–2000.
A working target for the lab dip. Not a licensed chip and not a lot standard.
- Weight
- 110 GSM (3.2 oz/yd²)
- Width
- 280 cm (110 in)
- Fiber
- 100% virgin polyester
- Weave
- Plain weave (1/1)
- Finish
- Scoured and heat-set
- Colour
- 12-4306 TCX Whisper White · #e7e2d6
If you add it, it prints on the draft. Download does not require email.
110 GSM · Plain weave (1/1) · Scoured and heat-set
Move the pointer or use arrow keys. The glass shows filaments and ply. Sett is a square-sett estimate.
8-field mill RFQ checklist and governing lab test standards
Every field in the PDF draft generator maps to a specific physical parameter and international verification standard:
| Specification field | Mill-ready example | Governing standard / tolerance |
|---|---|---|
| 1. Yarn count & filament (Warp × Weft) | 75D/72F DTY × 150D/144F DTY (100% polyester) | ISO 2060 / ASTM D1907 (±3% linear density) |
| 2. Thread density / sett | 112 × 76 ends × picks/in (44 × 30 /cm) — specify stage | ISO 7211-2 / ASTM D3775 (±2 ends/cm) |
| 3. Weave structure | 1/1 Plain, 2/1 Twill, 1 cm Dobby Satin Stripe, or Jacquard | ISO 3572 weave diagram & face orientation |
| 4. Processing stage & finish | Loom-state greige, PFD, piece-dyed peachskin, or C6 3-pass blackout | AATCC 22 (spray ≥90) / ISO 105-C06 (wash Grade 3–4+) |
| 5. Cuttable vs total width | 280 cm cuttable (284 cm overall including pinhole selvedges) | ISO 22198 / ASTM D3774 (−0 / +2 cm usable width) |
| 6. Areal weight (GSM & stage) | 95 GSM finished (±5%, i.e., 90–100 g/m²) | ISO 3801 / ASTM D3776 (100 cm² circular cutter) |
| 7. Shade & colorfastness target | Pantone 11-0602 TCX Snow White or CIE Whiteness ≥120 | CMC(2:1) ΔE ≤ 1.0 under D65 / TL84 primary illuminants |
| 8. Certification & inspection rule | OEKO-TEX Standard 100 + GRS TC; ASTM D5430 ≤28 pts/100 sq yd | ISO 2859-1 Level II (AQL 2.5) + Four-Point System |
Use the interactive form above to generate an aligned English spec sheet PDF, then attach it to your sample or bulk inquiry.
Specification tolerance and cuttable width formulas
Always state tolerances explicitly on the purchase order rather than relying on informal trade custom.
Acceptable GSM Band = Target GSM × (1 ± 0.05) [e.g., 100 GSM → 95–105 g/m²]
Cuttable Width (cm) = Total Finished Width (cm) − (2 × Selvedge Allowance [1.5–2.0 cm])
Common questions
- Is this a lab report?
- No. A working draft for alignment. Lab reports and GRS or OEKO-TEX documents are confirmed on the order.
- Why is the PDF in English?
- English export wording is the language of the mill PO.