Skip to content
Yarn

Denier yarn: what it means and how to convert it

Convert between denier, dtex, tex, and Ne, and read the filament diameter behind a denier.

What denier yarn means

Denier yarn is measured by mass per length: one denier is one gram per 9,000 metres of the strand. Lower denier is finer, higher is coarser — 75 D is a fine filament, 600 D a heavy one. The number describes the yarn, not the woven cloth. Cloth weight is GSM, grams per square metre, so a fine yarn in a dense sett can still make a heavy fabric.

Yarn
Denier yarn: what it means and how to convert it
Convert between denier, dtex, tex, and Ne, and read the filament diameter behind a denier.
Denier

Usual 20–600. Limit 1–3000.

Denier

75.0

dtex

83.33

tex

8.33

Ne

70.87

dtex = denier × 10/9. tex = denier / 9. Ne ≈ 5315 / denier.

What is denier?
Denier per filament
Total denier divided by filament count.
F

Usual 1–144. Limit 1–576.

dpf

2.08

Filament diameter
Diameter from the denier and the fibre's density, assuming a solid circular filament.

Diameter (µm)

87.7

Diameter (mm)

0.0877

Geometric diameter of a solid circular filament. A hollow, trilobal or bicomponent filament of the same denier is larger on its widest axis, so treat this as the nominal figure.

Denier and dtex conversion table

Common polyester filament counts, both directions. D = dtex × 0.9, so each row is the same yarn on two scales.

Denier (D)dtexTypical use
75 D83 dtexFine bed linen, microfiber-hand fabrics
100 D111 dtexFine sheers, soft bedding
150 D167 dtexStandard polyester home-textile warp and weft
200 D222 dtexMid-weight drapery
210 D233 dtexCommon in continental specs
300 D333 dtexCurtains, heavier bedding
400 D444 dtexUpholstery base cloth
600 D667 dtexTechnical and heavy furnishing
1000 D1111 dtexCoarse industrial and reinforcing yarn

The conversion formulas

D is denier, dtex is decitex, tex is grams per 1,000 m, and Ne is the English cotton count — an indirect count, so that relation is approximate.

D = dtex × 0.9

dtex = D ÷ 0.9

tex = D ÷ 9

Ne ≈ 5315 ÷ D

150 D is not 150 dtex

A bare 150 on a purchase order does not name the yarn. 150 dtex is 135 D — the same strand under a finer number — and 150 D is 167 dtex. Write the unit: 150 D / 167 dtex, or 135 D / 150 dtex. The gap is small enough to pass a sample and fail a bulk order.

Denier to millimetres: filament diameter

Denier is linear density, not diameter, so no single factor converts one to the other. A filament's diameter follows from its mass per length and the fibre's density.

For polyester, ρ = 1.38 g/cm³. For nylon, ρ ≈ 1.14 g/cm³. Diameter scales with √(1/ρ), so the same denier is a thicker filament in nylon: 1 denier is 10.1 µm in polyester and 11.1 µm in nylon.

Mass per length is D ÷ 9000 g/m. With ρ in g/cm³, that gives a cross-section area of D ÷ (9000 × ρ) mm², and the diameter of a circular filament follows from the area:

A (mm²) = D ÷ (9000 × ρ)

d (mm) = 2 × √(A ÷ π) = 2 × √(D ÷ (9000 × ρ × π))

Denier (D)Polyester (mm)Polyester (µm)Nylon (mm)
1 D0.0101100.0111
50 D0.0716720.0788
75 D0.0877880.0965
150 D0.12401240.1364

Diameters rounded; µm to the nearest micrometre. Values assume a circular filament.

Common questions

Is denier the same as GSM?
No. Denier is yarn. GSM is the woven fabric mass.
What is Ne here?
English cotton count as used on yarn conversion sheets, not a lab certificate.
How is yarn denier calculated from weight and length?
Denier = (Weight in grams × 9,000) / Length in meters. By definition, 1 Denier means that 9,000 meters of continuous yarn weighs exactly 1 gram.
How to convert Denier to Tex, Dtex, and English Cotton Count (Ne)?
Standard direct and indirect yarn conversion formulas: Tex = Denier / 9; Dtex = Denier × 1.111; Ne (cotton count) ≈ 5,315 / Denier; Nm (metric count) ≈ 9,000 / Denier.
What does DPF mean in polyester filament yarn?
DPF stands for Denier Per Filament, calculated as Total Denier / Filament Count. For example, 75D/72F has DPF ≈ 1.04. In textile specifications, microfiber is defined as any filament with DPF < 1.0.
How many millimetres is 1 denier?
About 0.0101 mm, or 10.1 µm, for polyester at ρ = 1.38 g/cm³. The answer depends on the fibre: nylon at ρ ≈ 1.14 gives 0.0111 mm. Denier is mass per length, so a diameter needs the density as well.