Skip to content

CIE Whiteness Index

A standard measurement scale used in the textile industry to quantify the degree of whiteness of a fabric, particularly important for bleached products and hotel linens.

The CIE Whiteness Index is the number the textile trade uses to say how white a fabric is. It exists because white is otherwise a matter of opinion: the index fixes an illuminant, an observer and a formula, so two labs can agree on whether a cloth is 150 or 160 — and a buyer can write a number on a PO instead of a word.

By Wren Thunderborn, Head of Content

Also known as: whiteness levelfabric whitenessCIE whiteness valueoptical whitenesscie whitecie whitenesswhiteness index

The CIE Whiteness Index is the number the textile trade uses to say how white a fabric is. It was standardised by the Commission Internationale de l'Éclairage (the International Commission on Illumination), and it exists because "white" is otherwise a matter of opinion: the same cloth looks white under one light and cream under another, which makes it impossible for a buyer in one country and a mill in another to agree on a specification.

The number is measured on a spectrophotometer, not calculated by hand, and one figure on a purchase order is worth exactly as much as the conditions it was taken under.

What the number means

100 is the neutral point. A perfectly reflecting, non-fluorescent white surface would measure exactly 100.

CIE whitenessWhat it meansWhere it sits
Below 100Still reads yellow-orientedA natural off-white, or a base that has not been bleached
Around 100The neutral pointA perfect diffuser would sit here
100–110Standard commercial whiteOrdinary consumer bedding and apparel
120 and aboveHigh white, "optical white"Premium hotel linen, medical textiles, bright retail bedding

Above 100 the sample reads as a blue-phase white, and below 100 it reads yellow-oriented. That single fact explains most of the trade's vocabulary: the optical brightening agents used in bleaching absorb invisible ultraviolet light and re-emit it as visible blue, cancelling the yellow that polyester carries out of the polymer and pushing the reading past 100.

So a CIE 120+ cloth is not just "whiter". It is a cloth where the brightener is doing visible work, which is why it costs more and why it is the tier the premium end asks for.

How the reading is taken

The index comes off a spectrophotometer that reads the sample's reflectance across the visible spectrum. Two things about the reading are as important as the number:

  • The illuminant and the observer have to be stated. A D65/10° combination is one of the most commonly reported in industry, but a number taken under one illuminant is not directly comparable with a number taken under another.
  • The sample has to be the finished cloth. A reading taken on greige, on a partially bleached intermediate, or on a finished fabric after a softening or an optical finish are three different numbers.

That is why the mill, not the buyer, is the party that reports the figure: the mill holds the instrument and knows what state the cloth was in when it was read.

Which whiteness index?

There is more than one, and this is the most common way a whiteness figure gets misread.

IndexNotes
CIE whitenessThe one the textile trade quotes; the one on a purchase order
Hunter whitenessA separate, older scale, still reported by some instrument makers
Ganz-Griesser whitenessA third scale, measured alongside the CIE value by some instrument suppliers

One white fabric can carry three different numbers depending on which index was read. The index name has to travel with the value — a "whiteness of 120" on its own does not identify a specification.

What it costs, and where it stops paying

Reaching 120+ takes more aggressive bleaching chemistry, better optical brighteners and tighter process control than a standard commercial white. All three cost money, and all three cost time.

The honest way to specify it is to work from the end use and pay only for what the end use needs:

  • Hotel linen, medical textiles and bright retail bedding — the cloth is seen under strong light and next to other whites, so 120+ is the tier that holds up.
  • Standard consumer bedding — a commercial white in the 100–110 range is enough, and specifying 120 there is paying for a number nobody will see.
  • Printing — the requirement is set by the lightest shade in the design, not by the design being dark or busy. A pale shade needs a white base to print against; a pigment print that covers the cloth does not.

Over-specifying whiteness is the expensive mistake, and under-specifying it is the embarrassing one: the second shows up as a batch that looks grey next to the rest of the order.

How buyers compare lots

A minimum on the purchase order is only half of it. The comparison that actually matters is between one roll and the next, and that is where most disputes come from.

  • Ask for the tolerance next to the number, not just the minimum. "CIE 120+" without a tolerance is not a specification.
  • Compare on the same instrument, under the same illuminant and observer, with the same sample conditioning.
  • Keep a sealed standard sample and compare each incoming lot against it under a fixed light box. Two readings that both pass the minimum can still differ visibly.
  • Read the spread across the lot, not only the average. A lot that averages 122 with a wide spread will still show panels that do not match.
  • Say what the number is measured on — the finished fabric, and after which finishes.

What goes on the order

  • The index and the value — "CIE whiteness 120+" rather than "white 120".
  • The illuminant and the observer the reading was taken under.
  • A tolerance, and whether it is a minimum, a target with a band, or a maximum.
  • What the value is measured on — the finished fabric, after which finishes.
  • A standard sample, sealed, for the incoming comparison.

A purchase order that says only "white" has specified nothing that two mills could interpret the same way.

What this mill quotes

Our own figure is on the bleached white: CIE whiteness 120+, from 2,000 metres, on a 100% polyester base woven in-house on 650+ waterjet looms. The greige it starts from is our own greige in programmes of 55–120 GSM and 160–330 cm, and the finished cloth can then go to piece dyeing from 3,000 metres or to printing on the same base.

Two honest notes for a buyer reading this page from outside the mill. First, whiteness is a finishing property, not a weaving one — the loom decides the construction and the greige, and the bleaching and optical brightening decide the number. Second, the value belongs to the finished cloth: the same greige put through two different finishing routes gives two different whiteness figures, which is why a whiteness requirement on a purchase order has to name the state of the cloth it applies to.

For programme questions on this mill — with the sealed sample and the end use — write to us through contact. For where whiteness sits in the preparation sequence, see PFD and RFD; for the base cloth itself, see greige fabric.

Common questions

What is the CIE whiteness index?

A single number that describes how white a surface looks, standardised by the CIE. It combines the sample's reflectance with its colour against the perfect diffuser of the standard observer. The neutral point is 100: a perfect reflecting, non-fluorescent white would measure exactly 100.

What does a CIE whiteness value of 120 mean?

That the sample is above the neutral point and reads as a blue-phase white. Above 100 an optical brightening agent is compensating for the yellow in the fibre; below 100 the sample still reads yellow-oriented. 120 and above is the tier the trade calls high white or optical white, and it is what premium hotel linen, medical textiles and bright retail bedding ask for.

How is the whiteness index calculated?

It is measured, not calculated by hand. A spectrophotometer reads the sample's spectral reflectance and returns the index. What does go into the number is the illuminant and the observer the reading was taken under, so a whiteness figure without those two stated is not comparable with another one.

What is the difference between CIE whiteness and Hunter whiteness?

They are different scales, and mixing them is the most common way a whiteness figure gets misread. CIE whiteness is the standard the textile trade quotes; Hunter whiteness is a separate, older scale, and there is also a Ganz-Griesser index. One white fabric can carry three different numbers. The index name has to travel with the value.

Is CIE 120 good enough for hotel linen?

For premium hotel linen and medical textiles, 120 and above is the tier to specify, because the cloth is seen under bright light and next to other whites. A standard commercial white in the 100 to 110 range suits much consumer bedding. For printing, the requirement is set by the lightest shade in the design, not by the design being dark or busy.

How do buyers compare whiteness between lots?

Measure on the same instrument and under the same illuminant and observer, and ask for the tolerance next to the number. Keep a sealed standard sample and compare against it under a fixed light box, because two readings of two rolls can differ even when both pass the minimum. Watch the spread across a lot, not only the average.

What is optical white?

The trade's name for the above-100, blue-phase white produced with optical brightening agents. It is not a different index: it is the same CIE whiteness scale in its upper band, where the brightener is doing the work of cancelling the natural yellow of the fibre.
Share:

Sourcing cie whiteness index or a polyester equivalent? We quote mill-direct programs from 5,000 m per specification.

Want to learn more textile terms?

Browse the full glossary
Weaverine manufacturing

Polyester home-textile fabric, woven mill-direct for buyers worldwide.

Our mills run 650+ waterjet looms and produce 73M+ meters annually for bedding, curtain, and upholstery fabric programs.

73M+
Meters per year
650+
Waterjet looms
200,000+
Meters per day