Nylon and polyester both run on a waterjet. What this mill does not have is a nylon yarn supply, acid-dye route or nylon programme — so a nylon brief is sourced elsewhere, not re-engineered here.
Nylon
A melt-spun polyamide filament — PA 6 or PA 6.6 — valued for abrasion resistance, elasticity and a moisture regain roughly ten times polyester's. A waterjet loom weaves both; this mill's programme, yarn supply and dye route are polyester, so nylon is a sourcing decision rather than a machine limit.
By Wren Thunderborn, Head of Content

Nylon is a polyamide. Polyester is a PET. Both are melt-spun synthetic filaments, both are woven on the same waterjets, and both are petrochemical. Almost everything buyers argue about comes from that one structural difference, so it is worth starting there rather than with a list of end uses.
This page is written from the polyester side: this mill weaves 100% polyester, so where nylon is the better fibre the page says so and says to source it elsewhere.
The numbers that decide the argument
| Property | Polyester (PET) | Nylon (PA 6 / 6.6) |
|---|---|---|
| Moisture regain | ~0.4% | ~4% — about ten times |
| Abrasion resistance | Good | Better |
| Tear and tensile strength | Good | Higher |
| Elasticity and recovery | Moderate | High |
| UV and sunlight | Stable | Yellows and weakens |
| Melting / softening | Higher (~250–260 °C) | Lower (PA 6 ~215–220 °C) |
| Dye route | Disperse, ~130 °C pressurised | Acid dyes, easier and brighter |
| Dimensional stability | High | Lower; more stretch |
| Cost | Lower | Higher |
Two of those rows decide most specifications on their own: moisture regain and UV. Everything else is a trade a buyer can weigh.
Why moisture regain changes the hand
Nylon's ~4% regain against polyester's ~0.4% is a tenfold difference in how much water the fibre itself holds. In practice:
- Nylon feels less clammy next to skin, which is why it dominates hosiery, swimwear and lingerie linings.
- Nylon dries more slowly for the same reason, which matters in a hotel laundry or a fast-turnaround programme.
- Neither is absorbent in the cotton sense. A moisture-wicking finish changes how fast sweat spreads across the surface; it does not turn polyester into a hydrophilic fibre.
That last point is the one most often blurred in marketing. Wicking and absorbency are different properties, and only one of them can be added by a finish.
Why UV decides curtains
Nylon yellows and loses strength under sunlight; polyester does not, to anything like the same degree. A curtain spends its life in exactly that exposure. Add nylon's lower softening point — it is a poorer candidate for anything heat-set or pressed hard — and the answer for window textiles stops being a preference and becomes a technical conclusion.
The same logic runs through bedding. Contract bedding is polyester because polyester survives two hundred industrial washes without changing dimensions, and because heat-setting holds shrinkage under 3%.
Where nylon genuinely wins
Being straight about this is what makes the comparison usable:
- Abrasion and tear — backpacks, luggage, down-proof shells, workwear knees. Nylon taffeta is the standard cloth for down jackets.
- Elasticity and recovery — swimwear, tights, anything that must return to shape.
- Bright, easy dyeing — acid dyes give deep, saturated shades at lower temperatures, which is why nylon dominates fashion colour ranges.
- Next-to-skin dryness — the 4% regain is a real comfort difference, not a marketing one.
If a programme's requirement sits in that list, nylon is the right fibre and a polyester mill should say so.
The honest boundary for this mill — and it is not the loom
This is the part that differs from the fibre pages where the machine is the limit. A waterjet weaves nylon perfectly well; nylon taffeta is produced on waterjets at scale.
What this mill does not have is a nylon programme: a polyamide yarn supply, an acid-dye route (its dyeing is built around disperse dyes at high temperature for polyester), the finishing know-how for a lower-softening-point fibre, and the certifications written against a polyester chain. Retrofitting that is a business decision, not a conversation about looms.
So the honest answer to "can you weave nylon?" is: the loom could, this mill does not, and a nylon brief is better sourced from a mill that runs polyamide.
Choosing between them, by end use
| End use | Better fibre | Why |
|---|---|---|
| Bedding, contract laundry | Polyester | Dimensional stability, heat setting, cost, wash life |
| Curtains, blackout, dimout | Polyester | UV stability; a coated polyester is the standard substrate |
| Awnings, marine covers | Polyester | UV and price |
| Down jackets, puffer shells | Nylon | Tear strength at low weight, down-proof density |
| Backpacks, luggage | Nylon | Abrasion and tear |
| Swimwear, hosiery, lingerie | Nylon | Elasticity and regain |
| Upholstery | Split | Polyester for cost and UV indoors; nylon for contract abrasion |
| Workwear | Split | Polyester for UV and cost; nylon for abrasion at stress points |
What goes on the order
Whichever fibre is chosen, the line has to name the polymer and the test:
- The polymer, not the trade word — PET, PA 6 or PA 6.6, because the dye route and the softening point follow from it.
- The dye class — disperse for polyester, acid for nylon — and the shade-fastness standard it must meet.
- Denier and filament count, since the hand and the tear strength come from the yarn, not the polymer name.
- The UV requirement, stated as an exposure standard if the article is outdoors or in a window.
- The abrasion standard if the end use is load-bearing, so "durable" becomes measurable.
- The finish and its substrate, because a water-repellent finish or a PA coating bonds differently on each polymer.
What this mill does
This mill weaves 100% polyester — not a blend, not a polyamide — on more than 650 waterjet looms: greige at 55–120 GSM and 160–330 cm, finished at 60–140 GSM and 150–315 cm, above 200,000 m/day, under OEKO-TEX STANDARD 100 with GRS chain of custody available on the recycled route.
For a programme that is comparing the two fibres, what this mill can do is put the polyester side into cloth: taffeta and pongee for shells and linings, water-repellent and PA-coated finishes for weather resistance, and denier control where the hand matters more than the weight.
For the fibre it does not run, the answer is a referral rather than a quotation. Stock greige carries no minimum; custom greige starts at 5,000 m and piece dyeing at 3,000 m per colour. Request a quote with the polymer, the weight and the end use, or see polyester fibre for what the mill does run.
Common questions
What is nylon made of?
- Polyamide. Nylon 6.6 is a condensation polymer of adipic acid and hexamethylene diamine; nylon 6 is polymerised from caprolactam. Both are melt-spun into continuous filament, which is why nylon cloth is smooth and strong rather than hairy. It is a thermoplastic, so it can be heat-set into a permanent shape — the reason nylon is the fibre behind tights, swimwear and parachutes.
What is the difference between polyester and nylon?
- Polyester is a polyester polymer (PET); nylon is a polyamide. The practical consequences are: nylon regains about 4% moisture against polyester's 0.4%, so it feels less clammy next to skin; nylon resists abrasion better; nylon takes bright acid dyes easily, while polyester needs disperse dyes at around 130°C; and nylon yellows and weakens in sunlight where polyester stays stable. Polyester is cheaper, more UV-stable and more dimensionally stable.
Which is better for curtains and bedding, polyester or nylon?
- Polyester, and the deciding factor is sunlight and heat. Nylon degrades and yellows under UV, which is exactly the exposure a curtain gets, and it softens at a lower temperature than polyester, so it is a poorer choice for anything ironed or heat-set. Polyester also costs less and holds its dimensions through repeated industrial laundering, which is why contract bedding is polyester.
Which is better for outerwear and bags, polyester or nylon?
- It depends on which property dominates. Nylon wins on abrasion and tear strength, which is why backpacks, luggage and down-proof shells are usually nylon taffeta. Polyester wins on UV stability and price, so awnings, marine covers and most promotional bags are polyester. In technical shells the two are often blended or layered rather than chosen.
Can the same loom weave nylon and polyester?
- Yes. Both are melt-spun filament yarns woven in a plain weave or a ripstop grid on the same waterjet, and nylon taffeta for down jackets is routinely woven that way. What differs is the rest of the chain: yarn supply, the dye class and its temperature, the finishing route, and the certifications. So for a mill the question is not capability but whether it runs that programme.
Is nylon more sustainable than polyester?
- Neither is sustainable in the abstract, and both are petrochemical. Nylon 6 can be depolymerised back to caprolactam and re-polymerised, which is a genuine closed-loop route that recycled nylon (from fishing nets and carpet) uses. Polyester's recycled route — rPET from bottles — is far more established in volume and is certifiable under GRS. Judge either by the certificate and the boundary, not by the fibre name.
Related Terms
Sourcing nylon or a polyester equivalent? We quote mill-direct programs from 5,000 m per specification.
Want to learn more textile terms?
Browse the full glossaryPolyester home-textile fabric, woven mill-direct for buyers worldwide.
Our mills run 650+ waterjet looms and produce 73M+ meters annually for bedding, curtain, and upholstery fabric programs.